Products

    Pages

        GLXP-HSW12

        12 Channel High-Inrush Switch Module

        • 12 channels of high-inrush power switching
        • Rugged, high-current latching relays
        • Supports 100 to 277 Volt applications

        The GLXP-HSW12 is a Crestron® Green Light® switching module which features 12 channels of high-inrush power switching with rugged, high-current latching relays. The module is part of a complete Crestron engineered GLPS

        Green Light switching panel.

        For more information on Crestron Green Light commercial lighting products, please contact Crestron Sales Support Services.

         
        Key Features
        • 12 channels of high-inrush power switching
        • Rugged, high-current latching relays
        • Supports 100 to 277 Volt applications
        • 16 Amp, 1 HP load rating per channel
        • Arc-less switching
        • Positive air gap at each output
        • Phase-independent channels
        • Cresnet® communications
        • Redundant power capability—module powered via line or Cresnet
        • Local controls for testing and verification
        • Local and remote override capability
        • Non-volatile power failure memory
        • GLEP cabinet installation
         
        Load Ratings
          Switch Channels 12
          Per Channel 16 Amps @ 100 to 277 Volts AC, 50/60 Hz;
        0.5 HP @ 120 Volts, 1 HP @ 230 Volts, 1 HP @ 277 Volts
          Switch Load Types Incandescent, Magnetic Low-Voltage, Electronic Low-Voltage, Neon/Cold Cathode, Fluorescent Ballast, High-Intensity Discharge, LED, Motor
          Relay Lifetime 1,000,000 on/off operations at full electronic ballast load
        Power Requirements
          Primary 100-277 Volts AC, 50/60Hz, supplied via channel 1 (L1, N1)
          Secondary (optional) 5 watts at 24 Volts DC, supplied via Cresnet®
        Connectors
          NET (2) 5-pin headers; connect to adjacent module or internal connecting block using interconnect cable (block and cable provided)
          N1 (1) terminal block, line input neutral
          L1-L12 (12) terminal blocks, line power inputs
          SW1-SW12 (12) terminal blocks, switch channel outputs
          Note: Line power terminal blocks accept 10-14 AWG wire; torque to 4.43 lb-in (0.5 Nm);
        Controls & Indicators
          NET ID (2) 7-Segment green LED digits and (2) miniature pushbuttons for setting Cresnet ID;
          SETUP (1) Red LED and (1) recessed miniature pushbutton for enabling setup mode and touch-settable ID
          OVR (1) Red LED and (1) miniature pushbutton for enabling override mode and saving override presets
          PWR (1) Green LED; solid illumination indicates line power is applied to N1 and L1; flashing indicates Cresnet power is supplied in absence of line power
          NET (1) Yellow LED; indicates communication with control processor
          RESET (1) Recessed miniature pushbutton, resets internal processor
          ON/OFF (12) Red LEDs and (12) miniature pushbuttons for individual manual channel activation
        Enclosure
          Surface mount module with (2) integral mounting flanges; mounts in a GLEP enclosure; (-LP) mounts in a GLEX enclosure
        Environmental
          Temperature 32° to 104°F (0° to 40°C)
          Humidity 10% to 90% RH (non-condensing)
          Heat Dissipation 160 BTU/Hr
        Dimensions
          Height 11.07 in (282 mm)
          Width 9.5 in (241 mm) including mounting holes
          Depth 4.78 in (121 mm) including standoffs
          Depth (-LP only) 3.07 in (78 mm)
        Electrical Regulatory Certifications
          UL508, Section 41 (Endurance Test) and Section 61C (Electronic Ballasts)
          UL924, Emergency Power Equipment
          IEC60669-2-1, Section 19.102 (Contact mechanisms incorporated in electronic switches, intended for fluorescent lamp circuits or other capacitive loads)
          SCCR Rating - 18kA
          CE