Products

    Pages

        GLXP-SW10

        10 Channel Switch Module

        • 10 channels of power switching
        • Mechanically-latching relays
        • Supports 100 to 277 Volt applications

        The GLXP-SW10 is a Crestron® Green Light® switching module which features 10 channels of power switching with rugged, high-current latching relays. The module is part of a complete Crestron engineered GLPS

        Green Light switching panel.

        For more information on Crestron Green Light commercial lighting products, please contact Crestron Sales Support Services.

         
        Key Features
        • 10 channels of power switching
        • Mechanically-latching relays
        • Supports 100 to 277 Volt applications
        • 16 Amp, 1 HP load rating per channel
        • Positive air gap at each output
        • Phase-independent channels
        • Cresnet® communications
        • Redundant power capability—module powered via line or Cresnet
        • Local controls for testing and verification
        • Local and remote override capability
        • Non-volatile power failure memory
        • GLEP cabinet installation
         
        Load Ratings
          Switch Channels 10
          Per Channel 16 Amps @ 100 to 277 Volts AC, 50/60 Hz;
        0.5 HP @ 120 Volts, 1 HP @ 230 Volts, 1 HP @ 277 Volts
          Switch Load Types Incandescent, Magnetic Low-Voltage, Electronic Low-Voltage, Neon/Cold Cathode, Fluorescent Ballast, High-Intensity Discharge, LED, Motor
          Relay Lifetime Resistive rating: 100,000 on/off operations, 50A @ 277 VAC
        General rating: 50,000 on/off operations, 16A @ 120/277 VAC
        Power Requirements
          Primary 100-277 Volts AC, 50/60Hz, supplied via channel 1 (L1, N1)
          Secondary (optional) 5 watts at 24 Volts DC, supplied via Cresnet®
        Connectors
          NET (2) 5-pin headers; connect to adjacent module or internal connecting block using interconnect cable (block and cable provided)
          N1 (1) terminal block, line input neutral
          L1-L10 (10) terminal blocks, line power inputs
          SW1-SW10 (10) terminal blocks, switch channel outputs
          Note: Line power terminal blocks accept 10-14 AWG wire; torque to 4.43 lb-in (0.5 Nm);
        Controls & Indicators
          NET ID (2) 7-Segment green LED digits and (2) miniature pushbuttons for setting Cresnet ID;
          SETUP (1) Red LED and (1) recessed miniature pushbutton for enabling setup mode and touch-settable ID
          OVR (1) Red LED and (1) miniature pushbutton for enabling override mode and saving override presets
          PWR (1) Green LED; solid illumination indicates line power is applied to N1 and L1; flashing indicates Cresnet power is supplied in absence of line power
          NET (1) Yellow LED; indicates communication with control processor
          RESET (1) Recessed miniature pushbutton, resets internal processor
          ON/OFF (10) Red LEDs and (10) miniature pushbuttons for individual manual channel activation
        Enclosure
          Surface mount module with (2) integral mounting flanges; mounts in a GLEP enclosure
        Environmental
          Temperature 32° to 104°F (0° to 40°C)
          Humidity 10% to 90% RH (non-condensing)
          Heat Dissipation 136 BTU/Hr
        Dimensions
          Height 7.5 in (191 mm)
          Width 9.5 in (241 mm)
          Depth 4.78 in (121 mm) including standoffs
        Electrical Regulatory Certifications
          UL508, Section 41 (Endurance Test) and Section 61C (Electronic Ballasts)
          UL924, Emergency Power Equipment
          IEC60669-2-1, Section 19.102 (Contact mechanisms incorporated in electronic switches, intended for fluorescent lamp circuits or other capacitive loads)
          SCCR Rating - 18kA
          CE