MediaManifold Cable Analyzer
This product has been discontinued. Please contact Crestron True Blue Support at 1-888-CRESTRON for a replacement solution or more information.
The Crestron MM-HTDR MediaManifold™ Cable Analyzer is a portable handheld device used to determine the length and integrity of RG6 cable runs. Using "time domain reflectometry," the MM-HTDR can measure cable lengths up to 1099 feet. When used in conjunction with the MM-DS-12 MediaManifold CATV Distribution System, the MM-HTDR can be used to set the optimum gain and tilt settings for each zone based on the length measured (up to 300 feet maximum). The MM-HTDR can also be used to determine if a cable is shorted. Single-button operation makes it simple to set up a complete MediaManifold system.
The Crestron MM-HTDR MediaManifold™ Cable Analyzer is a portable handheld device used to determine the length and integrity of RG6 cable runs. Using "time domain reflectometry," the MM-HTDR can measure cable lengths up to 1099 feet. When used in conjunction with the MM-DS-12 MediaManifold CATV Distribution System, the MM-HTDR can be used to set the optimum gain and tilt settings for each zone based on the length measured (up to 300 feet maximum). The MM-HTDR can also be used to determine if a cable is shorted. Single-button operation makes it simple to set up a complete MediaManifold system.
| Measurement |
| | Maximum Cable Length | 1099 feet |
| | Minimum Cable Length | 0 feet for open, 5 feet for shorted |
| | Resolution | 0.1 foot from 00.0 to 99.9, 1 foot from 100 to 1099 |
| | Forward Bandwidth | 54 MHz to 1 GHz |
| | Cable Velocity Factor | 0.60 to 1.00 (0.82 factory default) |
| Connectors |
| | 75 OHM CABLE | (1) F-type coaxial, female;
Connects to RG6 cable under test;
Impedance: 75 Ohms nominal |
| | TO MM-DS-12 | (1) 3.5mm TRS mini-phone jack;
Connects to the MM-DS-12* during setup;
6 foot (1.83 m) interface cable included |
| Controls and Indicators |
| | FEET | (1) 3-digit green LED display, displays cable length in feet |
| | CAL Λ, V | (2) miniature recessed pushbuttons, used to calibrate the MM-HTDR to a known cable length or velocity factor |
| | DEFAULT CAL | (1) miniature recessed pushbutton, resets calibration to factory default |
| | OPEN | (1) green LED, indicates cable under test is unterminated (normal) |
| | 75 OHMS | (1) yellow LED, indicates cable under test is terminated or connected to some device, measurement cannot be made |
| | SHORT | (1) red LED, indicates cable under test is shorted or connected to some device, measurement cannot be made |
| | LOW BATT | (1) red LED, indicates battery should be replaced |
| | START | (1) square pushbutton, initiates measurement process |
| Battery |
| | Type | 9 Volt disposable alkaline, 625 mAh (included) |
| | Usage | ~4 hours total (>10,000 measurements) |
| | Automatic Shutoff | ~5 seconds |
| Environmental |
| | Temperature | 41° to 104°F (5° to 40°C) |
| | Humidity | 10% to 90% RH (non-condensing) |
| Enclosure |
| | Black plastic handheld box installed in removable rubberized protective “boot” |
| Dimensions |
| | Height | 1.68 in (4.27 cm) |
| | Width | 3.95 in (10.04 cm) |
| | Depth | 6.12 in (15.55 cm) |
| Weight |
| | 0.83 lb (379 g) |
* Sold separately.
Click
here to search product certificates.
Please select your region below to see the appropriate Advertised Pricing.
