C2N-SDC-DC [Crestron Electronics, Inc.]

Products / Shades / Accessories / Third-Party Shade & Drapery Controllers / C2N-SDC-DC

C2N-SDC-DC

Shade and Drape Controller, 2 outputs for 24 VDC 2-wire bidirectional motors

The C2N-SDC-DC is a 2-channel Shade and Drape Controller designed to provide a convenient and cost-effective solution for controlling 24 Volt DC motorized shades and drapes.

Have a question?

Add to a Project

Resources

+ Specifications

+ Downloads & documentation

Find a Dealer

The C2N-SDC-DC is a 2-channel Shade and Drape Controller designed to provide a convenient and cost-effective solution for controlling 24 Volt DC motorized shades and drapes. The C2N-SDC-DC is a Cresnet® device with two independently controlled 24V DC outputs, each designed to provide standard up/down or open/close control of a conventional two-wire bidirectional type motor.

The C2N-SDC-DC mounts in the wall or ceiling using an off-the-shelf 4" square or 2-gang electrical box. Pushbuttons on the front of the unit allow for manual operation of the motors during installation and setup.

This product may be purchased from an authorized Crestron dealer. To find a dealer, please contact the Crestron sales representative for your area. A list of sales representatives is available online at www.crestron.com/salesreps or by calling 800-237-2041.

Specifications subject to change without notice. Crestron is not responsible for errors in typography or photography.

Crestron, the Crestron logo, and Cresnet are trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and other countries. Somfy is a trademark or registered trademark of Somfy Systems Inc. in the United States and other countries. Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of others. ©2012 Crestron Electronics, Inc.

Load Ratings
	Motor Control Channels	2
	Per Channel	30 Watts (1.25 Amps) @ 24 Volts DC
	Total	30 Watts (1.25 Amps) @ 24 Volts DC
	Load Type	2-Wire 24V DC bidirectional motors, Somfy® LT28B or similar
Power Requirements
	Cresnet Power Usage	Up to 33 Watts (1.38 Amps @ 24 Volts DC) depending on motor load, dedicated power supply recommended
Connections – Front Panel
	AB 1 – 2	(2) 2-pin 3.5mm detachable terminal blocks providing (2) 24V DC 2-wire bidirectional motor control outputs
	NET	(1) 4-pin 3.5mm detachable terminal block; Cresnet slave port, connects to Cresnet control network
Buttons
	1 UP/DOWN	(2) buttons for local control of output #1
	2 UP/DOWN	(2) buttons for local control of output #2
	SETUP	(1) button used for touch-settable ID (TSID)
LED Indicators
	PWR	(green) Indicates DC power supplied from Cresnet network
	NET	(yellow) Indicates communication with the Cresnet system
	SETUP	(red) used for touch-settable ID (TSID)
Environmental
	Temperature	41° to 122°F (5° to 50°C)
	Humidity	10% to 90% RH (non-condensing)
Enclosure
	Flat metal plate mountable in a 4-inch square or 2-gang electrical box, 1.5 inch minimum depth
Dimensions
	Height	4.10 in (104.2 mm)
	Width	4.10 in (104.2 mm)
	Depth	1.16 in (29.5 mm)
Weight
	0.55 lb (0.25 kg)